Release Notes
Product (s) : TekExpress 100G-TXE Solution
Version : Version 1.1.0
Last Revised : 16-Dec-2016

=====================================================================================
Contents:

1. Introduction
2. List of supported equipment’s
3. List of supported test
4. Changes/What's new in version 1.1.0
5. TekExpress Application created changes on your system
6. Recommendations
7. Known Limitations
7.1 Installer related limitation

=====================================================================================
1. Introduction

The Tektronix TekExpress 100G-TXE is an automated test solution for performing
100GBASE-CR4, 100GBASE-KR4 and CAUI4 tests.
- CAUI4, IEEE 802.3bm Specification, Annex 83E - TP1a and TP4
- 100GBASE-KR4, IEEE 802.3bj Specification, Section 93.8 - TP0a
- 100GBASE-CR4, IEEE 802.3bj Specification, Section 92.8 - TP2

=====================================================================================
2. List of supported equipment’s

Scope: DPS77004SX, DPO77002SX, DPS75904SX, DPO75902SX, DPS75004SX, DPO75002SX, DPO72304SX, DPO72304DX, MSO72304DX,
DPO72504DX, MSO72504DX, DPO73304SX, DPO73304DX, MSO73304DX

For Compliance testing minimum of 2 stacks SX scopes with Bandwidth >= 50GHz is recommended.

Supported Scope Version: 10.5.1 or greater
Supported DPOJET Version: 10.0.3 or greater

=====================================================================================
3. List of supported tests

3.1 For 100G-CAUI4(TP1a)
a) DC Common Mode Output Voltage
b) Diff Peak to Peak Output Voltage-Tx Disabled
c) Diff Peak to Peak Output Voltage-Tx Enabled
d) AC Common Mode Output Voltage
e) Single Ended Output Voltage
f) Signaling Rate
g) Eye Width
h) Eye Height Differential
i) Transition Time

3.2 For 100G-CAUI4(TP4)
a) DC Common Mode Output Voltage
b) Diff Peak to Peak Output Voltage-Tx Enabled
c) AC Common Mode Output Voltage
d) Signaling Rate
e) Eye Width
f) Eye Height Differential
g) Vertical Eye closure
h) Transition Time

3.3 For 100G-KR4(TP0a)/100G-CR4(TP2)
a) DC Common Mode Output Voltage
b) Diff Peak to Peak Output Voltage-Tx Disabled
c) Diff Peak to Peak Output Voltage-Tx Enabled
d) AC Common Mode Output Voltage
e) Signaling Rate
f) Transmitter Waveform Requirement
1. Signal to Noise and Distortion Ratio
2. Linear Fit Pulse Peak
3. Steady State Voltage
4. Minimum Pre-cursor full scale ratio
5. Minimum Post-cursor full scale ratio
6. Normalized Coefficient step size(C(-1), C(0) and C(1) increment & decrement step size)
g) Output Jitter
1. Even-Odd Jitter Peak to Peak
2. Effective Total Uncorrelated Jitter Peak to Peak
3. Effective Bounded Uncorrelated Jitter Peak to Peak
=====================================================================================
4. Changes/What's new in version 1.1.0
a) Optimizations in automation flow and measurement execution time
b) Support to run with CTLE0dB is added for CAUI4 in user defined mode

=====================================================================================
5. TekExpress 100G-TXE created changes on your system.

After first launch of "TekExpress 100G-TXE.exe" following changes take place in your Scope.
a) "My TekExpress" folder is created under "My Documents" folder of current user
NOTE: If a user with new login ID launches "TekExpress 100G-TXE.exe" ,
"My TekExpress" folder is created under "My Documents" of the new user.
b) "Untitled Session" folder is created under "100G-TXE" folder when the
application is launched and will be deleted after proper termination of the
application.
c) If user saves a session then all session files are saved under "100G-TXE"
folder accordingly. Note that each session has multiple files associated with it and do
not tamper with any of the session file(s) and/or folder(s) as this may result in loss
of data or corrupted session files.

=====================================================================================
6. Recommendations

Ensure that all the required instruments are properly warmed up, Signal Path Compensation
is performed, appropriate attenuators are used when connecting signal to ATI channels and
deskew is done.

=====================================================================================
7. Known Limitations

7.1 Installer related limitation
a) Installation of TekExpress and other software packages are installed on C:
drive only.
b) The available free space on C: drive must be minimum 2.2GB.

=====================================================================================